Traveler's Notebook: Adding Bands For Extra Functionality

The extra band in a traveler's notebook is used to connect multiple refills or inserts. The general rule of thumb is that a primary refill secured to the notebook cover using the center elastic cord serves as an anchor for the entire system, allowing you to add additional refills and accessories using connecting rubber bands. The rubber bands can be purchased pre-sized or made at home by measuring the height of the insert, cutting the elastic twice that long, and tying a knot at the end.

Jump bands are a simple piece of elastic that can be used to add extra inserts

To use a jump band, first, take your insert and tie the elastic around its spine. You want the elastic to be pulled snugly around the insert, but not too tight as to leave an indent. Then, take a second insert and slide it under the elastic on the outside of the spine. Now you have two inserts connected by one jump band!

You can add even more inserts by taking one of the connected inserts and sliding it under the elastic spine of your traveller's notebook cover. This will leave you with two inserts connected by the jump band, and one connected by the spine of the cover. You can then add another insert by sliding it under the jump band, nestled between the other two. And there you have it—three inserts held together by one jump band and the spine of your cover!

If you want to add even more inserts, you can use additional jump bands or try other methods such as connecting the first and third inserts with an elastic band and then sliding them into the cover under the spine elastic, with the second insert placed between them. With a bit of creativity and some extra elastics, the possibilities for expanding your traveller's notebook are endless!

You can buy pre-sized jump bands or make your own

If you want to add extra inserts to your traveller's notebook, you can use a jump band. Jump bands are simple pieces of elastic that you can use to add extra inserts to your notebook. They are usually made of 2mm elastic cording and come in different colours.

You can buy pre-sized jump bands from places like Etsy, or from your local craft store. If you want to make your own, all you need to do is measure the height of your insert, cut a length of elastic twice that long, and tie a knot in the end. You can also add an extra insert to your notebook by using one of the elastic bands that come with the notebook.

There are a few different ways to add multiple inserts to your notebook. One way is to attach the first insert to the notebook cover using the elastic cord, then place the second insert next to the first, closed spine-to-spine. Open both notebooks to their respective centres, then loop a connecting rubber band over both notebooks. In your original refill, the rubber band should sit alongside the elastic cord.

The extra bands that come with the starter kit are to fix a broken elastic band

The extra bands can be used to change the colour of the elastic that goes around the cover itself. They are also useful if you want to add more inserts to your notebook. If you want to add three inserts, for example, you can place the first and third insert back-to-back and set the second one aside. Then, open the first and third refills to their centres and attach them using a connecting rubber band. Close the two refills and set them face-down inside the cover, connected by the rubber band. Pull the middle refill underneath the centre elastic cord.

You can also use a jump band, a simple piece of elastic, to add extra inserts. You can buy pre-sized jump bands or make your own by measuring the height of your insert and cutting a length of elastic twice that long. Then, tie a knot in the elastic.

You can use a large-sized rubber band to add additional inserts

If you want to add more inserts to your traveller's notebook, you can use a large-sized rubber band. The rubber band will act as a jump band, allowing you to add extra inserts to your notebook. Jump bands are simply pieces of elastic that you can use to add extra inserts. You can buy pre-sized jump bands or make your own by cutting a length of elastic cord (around twice the height of your insert) and tying a knot in the end.

To add extra inserts to your traveller's notebook using a large-sized rubber band, first, attach your first insert to the notebook cover using the elastic cord. Then, take your second insert and place it next to the first, with the spines touching. Open both notebooks to their centres and hold the two covers together. Loop the rubber band over both notebooks; the rubber band should sit alongside the elastic cord in the original refill.

If you want to add a third insert, place the first and third inserts back-to-back and set the second insert aside. Open the first and third inserts to their centres and attach them together using a rubber band. Close the two refills and place them inside the notebook cover, with the spines touching. Gently pull the two notebooks apart and pull the elastic cord up between the two refills. Slip your middle refill underneath the elastic cord.

By using large-sized rubber bands, you can add extra inserts to your traveller's notebook and customise it according to your needs.

The primary refill secured to the notebook cover using the centre elastic cord acts as an anchor for the entire system

The Traveler's Notebook is a versatile system that allows users to carry multiple notebook refills inside a single cover. This means you can have a planner, notebook, and sketchbook with different types of paper all in one place. The primary refill secured to the notebook cover using the centre elastic cord acts as an anchor for the entire system, allowing you to add additional refills and accessories.

The process of setting up a Traveler's Notebook with multiple inserts might seem tricky at first, but it's quite straightforward once you get the hang of it. The key is to remember that the primary refill attached to the centre elastic cord of the notebook cover serves as the foundation for the rest of your setup.

To add more refills, you can utilise connecting rubber bands, also known as jump bands, which are simply pieces of elastic that help you attach extra inserts. These bands are readily available for purchase, or you can even make your own by measuring the height of your insert, cutting the elastic to twice that length, and tying a knot at the end.

With your connecting bands ready, you can start by attaching the first refill to the notebook cover using the centre elastic cord, just as you would with a single insert. For a two-refill setup, place the second refill next to the first, with their spines together, and then loop a connecting band over both notebooks, ensuring it sits alongside the elastic cord.

If you're going for a three-refill setup, it's best to start by deciding the order of your inserts. Place the first and third inserts back-to-back and set the second one aside. Open the first and third refills to their centres and attach them together using a connecting band. Close the refills and place them inside the notebook cover, with their spines together, and then gently pull the middle refill underneath the centre elastic cord.

By using the primary refill secured to the notebook cover as an anchor, you can easily expand your Traveler's Notebook to accommodate multiple inserts and accessories, creating a versatile and powerful tool for all your planning, note-taking, and sketching needs.

Frequently asked questions